The SucceX Mini F7 V3 TwinG // GYRO FUSION is the NEXT-GEN flight controller you need for your next build. This FC is ready for anything with 4 uarts With its clean intuitive layout, the SucceX MINI F7 V3 TwinG makes installation a breeze with a 4 pin connector for your VTX and an10 pin connector that allows simple plug and play connection with your 4in1 ESC.
But the real magic of this flight controller lies in its TWIN GYRO configuration.
The TwinG uses two identical gyros oriented side by side with one offset 90 degrees from the other. Betaflight uses GYRO FUSION to blend and average the information from both gyros to send a much cleaner signal to the PID loop controller! Less noise and fewer oscillations across the throttle band without adding any delay! Betaflight software filters can be lowered in most cases as well, which brings a significant decrease in delay.
With plenty of processing power and uarts, this is the perfect flight controller for long-range GPS builds. And the TwinG configuration makes it the perfect Fc for builds like macro quads, cinematic filming rigs and x-class racers that are a bit trickier to tune.
TwinG Gyro Setup
-The Betaflight target's default setting is ‘gyro_to_use = both’ / Gyro fusion is active!
-To check the current setting, please use CLI and type ‘get gyro’ to find the responding entry.
-Change the settings with ‘set gyro_to_use = ’ and type ‘save’.
-To get the most reliable performance or encounter noise, oscillation and bent props: Please use the default setting ‘both”.
-For Single Gyro use, please use the debugging options to find and tune for the cleaner gyro, but lose the dynamic fusion and averaging.
-BF offers the following dual gyro debug options: dual_gyro_raw, dual_gyro, dual_gyro_diff, dual_gyro_combined.
-BlackboxLog explorer graph: dual_gyro_raw Debugging =  Roll Gyro1,  Pitch Gyro1,  Roll Gyro2,  Pitch Gyro2.
-The displayed graph will show the Gyro_Raw reading (no filters applied), both gyros can be compared.
SucceX Mini F7 V3 Specifications
-Input voltage：2-6S,MAX 8S
Size:27*27mm /20*20mm φ3 mounting
- Mounting hole：20*20mm，φ3mm with Grommets φ2mm
SucceX Mini 35A V3 SPECS:
- MCU: STM32F051
- Current Sensor: Yes
- Input: 2-6s lipo
- Telemetry: Yes
- Installing Hole: 20x20mm, M3
- Target: iFlight-BL32-4IN1
- Constant: 35Amps
- Burst: 45Amps
- Dimensions: 31*31mm(including the power pads)
- Mounting Holes: 20*20mm
- Supports Dshot1200,Proshot,Oneshot,Multishot
5.8G VTX SPECS
-Input voltage: 2-6S
-48 standard channels, A/B/E/F/R Band
-Output Power: pit/20/100/200/500mW
-BEC Output: 5V/1A for Camera or FC
-RF Connector: MMCX
-Video Format: NTSC/PAL
-Size: 26*26mm /20*20mm φ3 mounting
-SucceX Mini F7 V3 TwinG FC+
-SucceX 35A V3 Plus BLHeli_32 4-in-1 ESC
-5.8G 500mW VTX
When you order from iflight-rc.com, you will receive a confirmation email. Once your order is shipped, you will be emailed the tracking information for your order's shipment. You can choose your preferred shipping method on the Order Information page during the checkout process.
The total time it takes to receive your order is shown below:
The total delivery time is calculated from the time your order is placed until the time it is delivered to you. Total delivery time is broken down into processing time and shipping time.
Processing time: The time it takes to prepare your item(s) to ship from our warehouse. This includes preparing your items, performing quality checks, and packing for shipment.
Shipping time: The time for your item(s) to tarvel from our warehouse to your destination.
Shipping from your local warehouse is significantly faster. Some charges may apply.
In addition, the transit time depends on where you're located and where your package comes from. If you want to know more information, please contact the customer service. We will settle your problem as soon as possible. Enjoy shopping!