SucceX-D F7 V2.1 Stack (F7+60A ESC)

SucceX-D F7 V2.1 Stack (F7+60A ESC)

$119.99
Product Code: FC07273

Available Options

Check out with PayPal

Product Description

The SucceX-D F7 is designed to work seamlessly with DJI’s new HD FPV system. To make things even simpler, the DJI Air unit can just be plugged into the FC with the included wire harness. In addition, we added the popular and reliable USB Type-C instead of Micro USB and therefore the same standard than your DJI module.

Features

• Universal USB Type C connector instead of micro USB

• Plug-and-Play. No need to solder tiny wires.)

• Supports BLHeli pass-through for easy ESC upgrade and configuration.

• Designed to support DJI Digital FPV.

FC // SucceX-D F7 TwinG

  • MCU: 216MHz STM32F722
  • Gyro:2x ICM20689
  • Baro: YES
  • Blackbox:32MB
  • Betaflight OSD: YES
  • BEC: 5V 2.5A / 9V 2.5A
  • Current sensor scale:  100
  • Inverter for SBUS input (UART2-RX)
  • Smartaudio & Tramp VTX protocol supported
  • Beeper pad : Yes
  • RSSI input pad: No
  • UARTs:5
  • Motor outputs: 8
  • 8 pin 4in1 ESC port (GND, VBAT, M1, M2, M3, M4, CUR, R5)
  • 6 pin DJI Air Unit port (R1, GND, R2, T2, GND, 9V)
  • BLHeli32 Telemetry:RX5
  • Input voltage:recommended 2-6S, MAX 8S
  • Target:   IFF_TWIN_G(IFRC)
  • Mounting pattern: 30.5*30.5mm φ4mm with Grommets φ3mm
  • Dimensions:   36*36mm
  • Weight: 7.5g
  • USB type-C

ESC // SucceX 60A V2 4in1

Top Features:

- 8 layers single-board stacking PCB board

- 4oz 1.6mm thick power board

- 32bit STM32FO51K MCU, 48kHz maximum clock speed

- TDK MLCC Low ESR ceramic capacitors

- Top grade metal MOSFET

Specification:

  • MCU: STM32F051
  • Up tp 48kHz PWM frequency
  • Capacitance: 470uF/50V
  • Current Sensor: Yes
  • Input: 2-6S LIPO
  • Constant: 60A / Burst: 80A
  • BlHeli32 telemetry: Yes
  • BEC: No
  • Supports up to Dshot1200, Proshot, Oneshot, Multishot 
  • Target: iFlight-BL32-4IN1
  • Weight:14.4g
  • Mounting pattern: 30.5*30.5mm/Φ3mm
  • Dimensions43*39mm (including the power pads)

Package included:

  • SucceX-D F7 TwinG FC x 1
  • SucceX 60A V2 ESC x 1

Betaflight target: IFF_TWIN_G (IFRC)

Downloads:

Please verify the latest Update on Github:

Betaflight_4.1.0_STM32F7X2 for DJI Air Unit

Betaflight 10.6.0 configurator for DJI Air Unit

To manually restore hardware related parameters using a unified target (STM32xxx targets), please paste following target config (DIFF) into your CLI:

IFLIGHTF7_TWIN_G.config

dont forget to save with the "save" CLI command.

Wiring Diagram *png:

SucceX-D F7 TwinG Manual

BLHeliSuite:

https://github.com/bitdump/BLHeli/tree/master/BLHeli_32%20ARM

TwinG Gyro Setup

-The Betaflight target's default setting is ‘gyro_to_use = both’ / Gyro fusion is active!

-RPM filter can be used with Gyro fusion in BF 4.1 and above! (Please check MCU load with the "tasks" CLI command)

-To check the current setting, please use CLI and type ‘get gyro’ to find the responding entry.

-Change the settings with ‘set gyro_to_use = ’ and type ‘save’.

-To get the most reliable performance or encounter noise, oscillation and bent props: Please use the default setting ‘both”. 

-For Single Gyro use, please use the debugging options to find and tune for the cleaner gyro, but lose the dynamic fusion and averaging.

-BF offers the following dual gyro debug options: dual_gyro_raw, dual_gyro, dual_gyro_diff, dual_gyro_combined.

-BlackboxLog explorer graph: dual_gyro_raw Debugging = [0] Roll Gyro1, [1] Pitch Gyro1, [2] Roll Gyro2, [3] Pitch Gyro2.

-The displayed graph will show the Gyro_Raw reading (no filters applied), both gyros can be compared.