SucceX-D Mini F7 TwinG Stack (Mini F7+40A ESC)

SucceX-D Mini F7 TwinG Stack (Mini F7+40A ESC)

$79.99
Product Code: FC07304

Available Options

Check out with PayPal

Product Description

The SucceX-D Mini F7 is designed to work seamlessly with DJI’s new HD FPV system. To make things even simpler, the DJI Air unit can just be plugged into the FC with the included wire harness. In addition, we added the popular and reliable USB Type-C instead of Micro USB and therefore the same standard than your DJI module.

But the real magic of this flight controller lies in its TWIN GYRO configuration.

The TwinG uses two identical gyros oriented side by side with one offset 90 degrees from the other. Betaflight uses GYRO FUSION to blend and average the information from both gyros to send a much cleaner signal to the PID loop controller! Less noise and fewer oscillations across the throttle band without adding any delay! Betaflight software filters can be lowered in most cases as well, which brings a significant decrease in delay.

With plenty of processing power and UARTS, this is also the perfect flight controller for long-range GPS builds. And the TwinG configuration makes it the perfect FC for builds like macro quads, cinematic filming rigs and x-class racers that are a bit trickier to tune.

FC // SucceX-D Mini F7

  • MCU: 216MHz STM32F722
  • Gyro:2x ICM20689
  • Blackbox:32MB
  • Betaflight OSD: YES
  • BEC: 5V 2.5A / 9V 2.5A
  • Current sensor scale:  100
  • Inverter for SBUS input (UART2-RX)
  • Smartaudio & Tramp VTX protocol supported
  • Beeper pad : Yes
  • RSSI input pad: No
  • UARTs:5
  • Motor outputs: 4
  • 8 pin 4in1 ESC port (GND, VBAT, M1, M2, M3, M4, CUR, R5)
  • 6 pin DJI Air Unit port (R1, GND, R2, T2, GND, 9V)
  • BLHeli32 Telemetry:RX5
  • Input voltage:recommended 2-6S, MAX 8S
  • Target:   STM32F7X2 (CLI config necessary; Check SETUP GUIDE above)
  • Mounting pattern: 20*20mm φ3
  • Dimensions:   29*29mm
  • USB type-C

ESC // SucceX 40A

  • MCU: STM32F051K66
  • Up tp 48kHz PWM frequency
  • Capacity: 470uF/50V
  • Current Sensor: Yes
  • Input: recommended 2-6S
  • Constant: 40A / Burst: 50A
  • BlHeli32 telemetry: Yes
  • Supports up to Dshot1200, Proshot, Oneshot, Multishot 
  • Target: iFlight-BL32-4IN1
  • Weight: 7.2g
  • Mounting pattern: 20*20mm φ3mm with Grommets φ2mm
  • Dimensions31*31mm (including the power pads)

Package included:

  • 1pc x SucceX-D F7 Mini TwinG Flight Controller
  • 1pc x SucceX Mini 40A 4in1

PLEASE CHECK OUR SETUP GUIDE AND WIRING DIAGRAM ABOVE

Please verify the latest version of Betaflight on Github, our download links might be outdated!

SucceX-D Mini F7 Twin_G (betaflight 4.1.0)

Betaflight 4.x introduced new so-called "Unified Targets", which is a radical change and a new approach for boards with similar MCUs (F4, F7, etc.) to reduce the amoints of targets around.

More information available here: https://betaflight.com/news/new-target-requirements/

To restore hardware related parameters, please paste following target config (DIFF) into your CLI after every betaflight reflash:

SucceX-D Mini F7 TwinG Target config(DIFF)

Don't forget to save with the "save" CLI command.

Wiring Diagram *png:

SucceX-D Mini F7 TwinG Manual

BLHeliSuite:

https://github.com/bitdump/BLHeli/tree/master/BLHeli_32%20ARM

TwinG Gyro Setup

-The Betaflight target's default setting is ‘gyro_to_use = both’ / Gyro fusion is active!

-RPM filter can be used with Gyro fusion in BF 4.1 and above! (Please check MCU load with the "tasks" CLI command)

-To check the current setting, please use CLI and type ‘get gyro’ to find the responding entry.

-To get the most reliable performance or encounter noise, oscillation and bent props: Please use the default setting ‘both”. 

-For Single Gyro use, please use the debugging options to find and tune for the cleaner gyro, but lose the dynamic fusion and averaging.

-BF offers the following dual gyro debug options: dual_gyro_raw, dual_gyro, dual_gyro_diff, dual_gyro_combined.

-BlackboxLog explorer graph: dual_gyro_raw Debugging = [0] Roll Gyro1, [1] Pitch Gyro1, [2] Roll Gyro2, [3] Pitch Gyro2.

-The displayed graph will show the Gyro_Raw reading (no filters applied), both gyros can be compared.

Write a review

Choose a file or drag it here.
Note: HTML is not translated!
    Bad           Good
Captcha

When you order from iflight-rc.com, you will receive a confirmation email. Once your order is shipped, you will be emailed the tracking information for your order's shipment. You can choose your preferred shipping method on the Order Information page during the checkout process.

The total time it takes to receive your order is shown below:

The total delivery time is calculated from the time your order is placed until the time it is delivered to you. Total delivery time is broken down into processing time and shipping time.

Processing time: The time it takes to prepare your item(s) to ship from our warehouse. This includes preparing your items, performing quality checks, and packing for shipment.

Shipping time: The time for your item(s) to tarvel from our warehouse to your destination.

Shipping from your local warehouse is significantly faster. Some charges may apply.

In addition, the transit time depends on where you're located and where your package comes from. If you want to know more information, please contact the customer service. We will settle your problem as soon as possible. Enjoy shopping!

Support